MPS400 Modular Product System Automation Production- Handling System Trainer (OMRON PLC based )school equipment teaching
I.Main features
1. The design of double-sided experiment platform can satisfy two groups of students at the same time. The components, circuits and electrical control of the two sides are independently controlled, and the experiment is not interfered with each other.
2. The modular structure design of structures, the experiment is simple, convenient, various pneumatic components into separate modules, with convenient installation plate, the experiment can freely on general aluminum plate, when assembling various experimental circuits, the operation is simple and convenient.
3. Quick and reliable connection, easy installation and convenient connection.
4. Standard industrial components, reliable edge and safety.
5. The laboratory has a computer communication interface which can be controlled with PLC programming device;
6. The gas source adopts the no-oil silent air compressor, which has the characteristics of low noise (< 55db). The gas is odorless and tasteless and clean and dry.
7. Multiple control methods: single pneumatic control circuit, electric control pneumatic circuit with relay, PLC control pneumatic circuit, etc.
II.Training workbench
1. The experimental platform adopts double-sided structure, which effectively saves the laboratory land and has a high cost performance.
2. The laboratory bench is made of high quality steel frame and high quality cold rolled steel.
The lower part of the platform has components and tool-storage cabinets.
The actual training screen is specially designed for the special belt "T", which can be easily and freely installed with pneumatic components and connected with the experimental circuit.
Pneumatic and electro-pneumatic with double face
- for 2 workstations
- each bench is composed by stainless steel structure for mounting and must be provided fully equipped
- the bench should be mounted on rollers and equipped with drawers
- equipment must be industrial grade
Equipped by:
- power supply
- pneumatic group composed by: pressure regulator, manometer, filter, cross connect
- necessary tools for studying industrial pneumatic, electro-pneumatic and proportional electro-pneumatic
III.Experiment list
Basic pneumatic
1) function demonstration experiment of common pneumatic components;
2) common pneumatic circuit demonstration experiment:
3) the commutation circuit of the single-acting cylinder
4)The reverse circuit of the double acting cylinder
5) the speed regulation loop of single-acting cylinder (one-way, two-way)
The speed regulating circuit of inlet speed of double acting cylinder
7) the speed regulating circuit of the speed adjustment of the two acting cylinder
8) speed switching circuit
9) the buffer circuit of parallel throttle valve is adopted
10) interlocking loop
11) overload protection loop
12) unloading loop
13) single cylinder continuous reciprocating control loop
14) two - cylinder continuous reciprocating control loop
15) use the cylinder sequence of the stroke valve
16) double cylinder sequence action loop with electrical switch (magnetic switch, proximity switch)
17) multi-cylinder sequential action loop
18) two - cylinder synchronous motor loop
19) secondary pressure control circuit
20) high and low voltage conversion circuit
21)Counting loop
22) delay loop
23) the hand operating circuit
24) the application circuit of the valve
25) or the application circuit of the door - type shuttle valve
26) quick exhaust valve application circuit
Electro pneumatic with PLC
1) PLC instruction programming, trapezoidal programming learning
2) the learning and use of PLC programming software(we supply free edition(free editon) software with unlimited users)
3) PLC and computing communication, online debugging
4) control experiment of PLC and pneumatic combination
IV.Components
Basic pneumatic components for each bench :
- 2 switch buttons 3/2, normally closed
- 1 switch button 3/2, normally open
- pressure indicator with 2 colors
- manual selector 5/2
- push-pull button 3/2 normally closed
- roller operated valve 3/2 normally closed
- 2 proximity sensors, pneumatic fixed on the actuator
- 2 pneumatic temporizers, normally closed
- sequence valve
- unilateral 3/2 distributor, with pneumatic command
- unilateral 5/2 distributor with pneumatic command
- bi-lateral 5/2 bi-stable distributor, with pneumatic command
- OR logic function
- & logic function
- fast evacuating valve
- 2 unidirectional flow limiters
- simple effect actuator
- double effect actuator
- pressure filter-regulator with pressure supply distributor
- pressure regulator with manometer
- 2 manometers
- air cross connect
- 2 plastic hoses
- pneumatic motor
- pneumatic sequencer
Basic electro-pneumatic components for each bench:
- electric buttons module
- electric relays module
- temporized relays module
- electronic pre-selection counter module
- emergency stop button
- inductive proximity sensor
- capacitive proximity sensor
- distributor terminal
-swing check valve
- electro-distributor with LED
- manometer
- pressure supply distributor with filter pressure reducer
Pneumatic regulation components:
- electric buttons module
- push button normally closed
- proportional electro-distributor (5/3, …)
- electro-distributor with LED (5/3 normally closed, 3/2 normally closed, …)
- monometer
- unidirectional flow limiter
- pressure supply distributor with filter pressure reducer
- air cross connect
- plastic hoses
- linear actuator, with guidance and all necessary accessories
- PID regulator
- comparison card
- analog pressure sensor
- pneumatic capacitors
- status regulator
- all necessary accessories for pneumatic regulation (potentiometer, damper, weight, …)
PLC equipped at least by:
- 24 VDC power supply
- Processor: 192 k bytes or better, memory 512 K bytes or better
- network interfacing (Profinet, Ethernet, USB, …)
- 16 digital inputs 24 VCC, potential separation LED light indication
- 16 digital outputs 24 VCC, 0.5A with galvanic separation and protection against short circuit
- 2 analog inputs
- 2 analog outputs
Supplied with Siemens S7-314CPLC:
- multi-users software teaching edition PLC programming including different languages(we supply free edition(free editon) software with unlimited users)
- connection PC-PLC
- spare parts set
- accessories set:
. electrical wires
. plastic hoses
. hoses connecting tools
. spare parts of first use
- practice activities manual book
- instruction book for the teacher including solutions for the practice activities
- silent air compressor with 30L, 8 bars minimum
- multi-users software for pneumatic and electromagnetic circuit simulation.
Product Details and Warranty
We supply suitable spare pats according to experiment requirement, our products take aluminum structure, A4 paper dimension aluminum and plastic hanging box structure.
We supply 3 years warranty time. Please se photo for foreign sales department and photo for spare parts.
Packaging & Delivery
Package details: plastic film+ plastic foam + plywood box with pallet, and for equipment dimension less than 1CBM, we supply plastic film+ plastic foam+ fine carton.
Arrange delivery within 45 days upon receipt of payment.
Please see below photo for detailed package.
Company Information
We supply professional educational training equipment and technical teaching equipment, which has been widely applied in Engineering Universities, Polytechnics, Technical Institute, Vocational Schools as well as Industry workforce Development Programs and Training Center. Our products allow students to learn and experiment through valuable hands-on experience, and the technology covered by our training equipment provides knowledge, experiments and didactic skills development that are of critical importance to today's and tomorrow's careers.
Photo for Clients Visiting Factory
Photo for Workshop and Equipments
Service
We supply supply7*24 hours service, customer design service, OEM service, buyer label service. With professional engineers team and sales team, we assure you good product quality.
Certificate
Our products takes ISO9001 product management system.
|
No. |
Feature Name |
Details |
|
1 |
Customer design |
Yes |
|
2 |
Warranty |
1 year, 2 years, 3 years or 5 years according to client requirements |
|
3 |
Package |
Plastic film+ carton+ Fine plywood |
|
4 |
Products standard |
International didactic equipment standard |
|
5 |
Application range |
Educational equipment for university, college, vocational training centers |
|
6 |
Company philosophy |
Supply best quality Chinese products to the worldwide schools. |
|
7 |
Self owned brand |
Shouldshine, SSEDU, JSS. |
|
8 |
Production time |
From 10 days to 60 days according to different items |
Audited Supplier 
){kind=link}