ZM3199 SSEDU Motion Control Trainer mechatronics training equipment educational equipment teaching vocational education training equipment Jinan
Motion control training equipment
Overview:
This device can realize the sensor detection, transaction processing, intelligent control and execute drive of production line. It refer to basis specialized knowledge and basis electromechanical skill requirement of mechanical technique, micro electronic technique, electrical and electronic technology, sensor detection technology, interface technology, information transformation technology, network communication technology and other mechatronics major.
Function characteristic:
- This system adapt industrial aluminum profile structure, the aluminum rail type training workbench is equipped with three basic unit: small car back and forth movement( pay-off ), three degree of freedom manipulator( carry ), sensor detection( material identification, distance detection, count, etc ), it can be used for single actuator, it also can make up a machinery platform of typical automatic production line.
- System mechanism adapt cylinder driver, frequency conversion adjustable-speed motor driver, DC motor driver. PLC and transducer control interface totally open, it can arbitrary outer connect control, it can adapt module combined type structure, each working unit are relatively independent module, it adapt standard structure and drawer type module, it has stronger interchangeability.
3. Manipulator mechanism hardware protection circuit. It can carry out judge the position signal of manipulator and output signal of PLC, the actuating signal of accord with logical function is manipulator response actuating signal, otherwise, it will failure to actuate, thus it realize machinery coordinate protection.
4. It is equipped with various industry common sensor, promote the signal data collection ability of equipment, it is convenient for student programme and the reliable of whole mechanism operation. It can make the student master the principle of various sensor and the application of practical work, use different sensor to realize different or same function.
5. According to upper computer WINCC configuration software to carry out networking communications, it can support 485, MODBUS, DP network and Ethernet to carry out data exchange.
Specification:
1.Boundary dimension: 1240(L)× 720(W)× 1300(H) mm (drawer don't stretch out)
2.Max. Sorting speed: 20 times/ minute
3.Continuous automatic sorting operation time: 24hours continuous sorting times: 28800times/day
4.Rated working power supply: AC:220V 50 Hz Main work power:1.2 Kw
5.Rated working air pressure: 0.3-0.4 MPa
6.Work environment: temperature-10ºC~35ºC relative humidity≤85%(25ºC)
Equipment constitute:
| No |
Component name |
Unit |
Quantity |
| 1 |
Equipment stand |
Set |
1 |
| 2 |
Feed mechanism |
Set |
1 |
| 3 |
Pneumatic manipulator |
Set |
1 |
| 4 |
Material sorting mechanism |
Set |
3 |
| 5 |
Sensor detection mechanism |
Set |
1 |
| 6 |
Silence type compress air pump |
Piece |
1 |
Supportable experiment training content:
1. The installation and commission of pneumatic system
(1)The installation of pneumatic direction control circuit
(2)The installation of pneumatic speed control circuit
(3)The installation of pneumatic sequence control circuit
(4)The installation of pneumatic manipulator
(5)The connection of pneumatic system gas circuit
(6)The position adjustment magnet switch
(7)Pneumatic system commission
(8)The installation of swing control circuit
2. The installation and commission of transducer
(1)The connection of transducer and AC motor main circuit
(2)The parameter setting and operation of transducer panel
(3)The speed governing of transducer panel control AC motor
(4)Control the motor and start and stop according to transducer external terminal
3. The installation and commission of electromechanical equipment
(1)The adjustment of transmission device coaxiality
(2)The installation and adjustment of belt conveyor
(3)The installation and commission of carry manipulator
(4)The installation and commission of article sorting equipment
(5)The installation and commission of feed equipment
(6)The installation and commission of automatic protection line.
4. The installation of electrical control circuit and PLC programming
(1)The connection and writing program of motor positive and negative going motion control circuit.
(2)The connection and writing program of motor speed governing control circuit
(3)The writing detection program of belt
(4)Pneumatic sequential action control programming
(5)Pneumatic manipulator control programming
(6)Mechatronics equipment control programming
(7)Automatic protection line control programming
5. The installation and commission of automatic control system
(1)The installation and commission of various sensor
(2)The automatic control of belt transport detection
(3)The automatic control of manipulator
(4)The automatic control of mechatronics
(5)The installation and commission of PLC control system
(6)The installation and commission of automatic protection line
6. The basic control and setting of touch screen
(1)The touch screen wiring and basic parameter setting
(2)The basic instruct programming of control type based on touch screen
(3)PLC, touch screen and transducer communication control
7. The operation training of communication engineering
(1)The network communication technology based on fieldbus
(2)The data communication and control training based on DP network
(3)The data communication and control training based on MODBUS network
(4)The data communication and control training based on Ethernet
(5)The data communication and control training based on 485 way
(6)The programming and communication control of WINCC configuration software
III.Experiment list
Basic pneumatic
1) function demonstration experiment of common pneumatic components;
2) common pneumatic circuit demonstration experiment:
3) the commutation circuit of the single-acting cylinder
4)The reverse circuit of the double acting cylinder
5) the speed regulation loop of single-acting cylinder (one-way, two-way)
The speed regulating circuit of inlet speed of double acting cylinder
7) the speed regulating circuit of the speed adjustment of the two acting cylinder
8) speed switching circuit
9) the buffer circuit of parallel throttle valve is adopted
10) interlocking loop
11) overload protection loop
12) unloading loop
13) single cylinder continuous reciprocating control loop
14) two - cylinder continuous reciprocating control loop
15) use the cylinder sequence of the stroke valve
16) double cylinder sequence action loop with electrical switch (magnetic switch, proximity switch)
17) multi-cylinder sequential action loop
18) two - cylinder synchronous motor loop
19) secondary pressure control circuit
20) high and low voltage conversion circuit
21)Counting loop
22) delay loop
23) the hand operating circuit
24) the application circuit of the valve
25) or the application circuit of the door - type shuttle valve
26) quick exhaust valve application circuit
Electro pneumatic with PLC
1) PLC instruction programming, trapezoidal programming learning
2) the learning and use of PLC programming software(we supply free edition(free editon) software with unlimited users)
3) PLC and computing communication, online debugging
4) control experiment of PLC and pneumatic combination
IV.Components
Basic pneumatic components for each bench :
- 2 switch buttons 3/2, normally closed
- 1 switch button 3/2, normally open
- pressure indicator with 2 colors
- manual selector 5/2
- push-pull button 3/2 normally closed
- roller operated valve 3/2 normally closed
- 2 proximity sensors, pneumatic fixed on the actuator
- 2 pneumatic temporizers, normally closed
- sequence valve
- unilateral 3/2 distributor, with pneumatic command
- unilateral 5/2 distributor with pneumatic command
- bi-lateral 5/2 bi-stable distributor, with pneumatic command
- OR logic function
- & logic function
- fast evacuating valve
- 2 unidirectional flow limiters
- simple effect actuator
- double effect actuator
- pressure filter-regulator with pressure supply distributor
- pressure regulator with manometer
- 2 manometers
- air cross connect
- 2 plastic hoses
- pneumatic motor
- pneumatic sequencer
Basic electro-pneumatic components for each bench:
- electric buttons module
- electric relays module
- temporized relays module
- electronic pre-selection counter module
- emergency stop button
- inductive proximity sensor
- capacitive proximity sensor
- distributor terminal
-swing check valve
- electro-distributor with LED
- manometer
- pressure supply distributor with filter pressure reducer
Pneumatic regulation components:
- electric buttons module
- push button normally closed
- proportional electro-distributor (5/3, …)
- electro-distributor with LED (5/3 normally closed, 3/2 normally closed, …)
- monometer
- unidirectional flow limiter
- pressure supply distributor with filter pressure reducer
- air cross connect
- plastic hoses
- linear actuator, with guidance and all necessary accessories
- PID regulator
- comparison card
- analog pressure sensor
- pneumatic capacitors
- status regulator
- all necessary accessories for pneumatic regulation (potentiometer, damper, weight, …)
PLC equipped at least by:
- 24 VDC power supply
- Processor: 192 k bytes or better, memory 512 K bytes or better
- network interfacing (Profinet, Ethernet, USB, …)
- 16 digital inputs 24 VCC, potential separation LED light indication
- 16 digital outputs 24 VCC, 0.5A with galvanic separation and protection against short circuit
- 2 analog inputs
- 2 analog outputs
Supplied with Siemens S7-314CPLC:
- multi-users software teaching edition PLC programming including different languages(we supply free edition(free editon) software with unlimited users)
- connection PC-PLC
- spare parts set
- accessories set:
. electrical wires
. plastic hoses
. hoses connecting tools
. spare parts of first use
- practice activities manual book
- instruction book for the teacher including solutions for the practice activities
- silent air compressor with 30L, 8 bars minimum
- multi-users software for pneumatic and electromagnetic circuit simulation.
Product Details and Warranty
We supply suitable spare pats according to experiment requirement, our products take aluminum structure, A4 paper dimension aluminum and plastic hanging box structure.
We supply 3 years warranty time. Please se photo for foreign sales department and photo for spare parts.
Packaging & Delivery
Package details: plastic film+ plastic foam + plywood box with pallet, and for equipment dimension less than 1CBM, we supply plastic film+ plastic foam+ fine carton.
Arrange delivery within 45 days upon receipt of payment.
Please see below photo for detailed package.
Company Information
We supply professional educational training equipment and technical teaching equipment, which has been widely applied in Engineering Universities, Polytechnics, Technical Institute, Vocational Schools as well as Industry workforce Development Programs and Training Center. Our products allow students to learn and experiment through valuable hands-on experience, and the technology covered by our training equipment provides knowledge, experiments and didactic skills development that are of critical importance to today's and tomorrow's careers.
Photo for Clients Visiting Factory
Photo for Workshop and Equipments
Service
We supply supply7*24 hours service, customer design service, OEM service, buyer label service. With professional engineers team and sales team, we assure you good product quality.
Certificate
Our products takes ISO9001 product management system.
|
No. |
Feature Name |
Details |
|
1 |
Customer design |
Yes |
|
2 |
Warranty |
1 year, 2 years, 3 years or 5 years according to client requirements |
|
3 |
Package |
Plastic film+ carton+ Fine plywood |
|
4 |
Products standard |
International didactic equipment standard |
|
5 |
Application range |
Educational equipment for university, college, vocational training centers |
|
6 |
Company philosophy |
Supply best quality Chinese products to the worldwide schools. |
|
7 |
Self owned brand |
Shouldshine, SSEDU, JSS. |
|
8 |
Production time |
From 10 days to 60 days according to different items |
Audited Supplier 
){kind=link}
){kind=link}